一篇文章翻译成英语把 谢谢

Question

压铸是压力铸造的简称，其实质是在高压作用下，是液态或半液态金属以较高的速度充填压铸模型腔，并在压力下成型和凝固而获得铸件的方法。
本设计进行了一次圆盘的压铸模设计，对零件结构进行了工艺分析。确定了分型面、浇注系统等，选择了压铸机，计算了成型零部件的尺寸。此模具的浇口形式采用侧浇口，利用四根导柱导向，推管顶料完成开模方向脱模，用复位杆进行复位，同时采用了四只推板导柱对推板进行导向，如此设计出的模具结构是为了确保模具工作运用可靠。最后对模具结构与压铸机的匹配进行了校核,并用AutoCAD和UG绘制了一套二维和三维模具装配图和零件图。

Answer 1

Die casting under pressure is the abbreviation, its essence is under pressure, in a liquid or half the liquid metal in high speed casting model, and filling in the cavity pressure molding and solidification and casting method.
The design of a disc mould design, process of parts structure analysis. Determine the parting surface, gating system etc, choose the molding machines, calculate the size of the parts. The mould runner form by using side gate, four guide pin, push pipe roof material, finished with open mold parting direction to reset, and reset pole adopts four pillars of push board guide plate orientation, so the mould structure was designed to ensure reliable mould work. Finally in the mould structure and casting of matching with AutoCAD checks, and draw a set of UG two-dimensional and three-dimensional mold assembly and detail drawings.

Answer 2

Die casting under pressure is the abbreviation, its essence is under pressure, in a liquid or half the liquid metal in high speed casting model, and filling in the cavity pressure molding and solidification and casting method.
The design of a disc mould design, process of parts structure analysis. Determine the parting surface, gating system etc, choose the molding machines, calculate the size of the parts. The mould runner form by using side gate, four guide pin, push pipe roof material, finished with open mold parting direction to reset, and reset pole adopts four pillars of push board guide plate orientation, so the mould structure was designed to ensure reliable mould work. Finally in the mould structure and casting of matching with AutoCAD checks, and draw a set of UG two-dimensional and three-dimensional mold assembly and detail drawings

参考资料：有道翻译

本回答被网友采纳

Answer 3

Pressure die casting is short, its essence is under high pressure, a liquid or semi-liquid metal to a high speed filling chamber die casting model, and under the pressure of molding and casting solidification method obtained.
The design of a disk of die casting mold design, part of the structure of the process. Identified sub-surface, casting system, select the die-casting machine to calculate the size of the molding parts. This form of the mold gate side of the gate with the use of four guide pillars oriented, push tube top mold the direction of mold release material to complete, reset the bar with a reset at the same time using four push plate guide pin on the push plate oriented die structure so designed to ensure reliable use of the die. Finally, the die structure and die-casting machine were checked the matching and mapping using AutoCAD and UG a two-dimensional and three-dimensional mold assembly drawings and parts drawing.

Answer 4

The compression casting is the pressure casting abbreviation, its essence is under the high-pressured function, is the liquid state or half liquid metal by the high speed backfill compression casting model cavity, and the formation and the coagulation obtains the casting under the pressure the method. This design has carried on a disc's pressure mold design,
The design of a disk of die casting mold design, part of the structure of the process. Identified sub-surface, casting system, select the die-casting machine to calculate the size of the molding parts. This form of the mold gate side of the gate with the use of four guide pillars oriented, push tube top mold the direction of mold release material to complete, reset the bar with a reset at the same time using four push plate guide pin on the push plate oriented die structure so designed to ensure reliable use of the die. Finally, the die structure and die-casting machine were checked the matching and mapping using AutoCAD and UG a two-dimensional and three-dimensional mold assembly drawings and parts

Answer 5

The compression casting is the pressure casting abbreviation, its essence is under the high-pressured function, is the liquid state or half liquid metal by the high speed backfill compression casting model cavity, and the formation and the coagulation obtains the casting under the pressure the method. This design has carried on a disc's pressure mold design, has carried on the process study to the components structure. Had determined a minute profile, the gating system and so on, has chosen the die-casting machine, has calculated the formation spare part size. This mold's runner form uses the edge gate, uses four guide pillar guidances, the ejector sleeve top material completes the die sinking direction drawing of patterns, carries on the replacement with the release link, simultaneously used four push pedal guide pillars to carry on the guidance to the push pedal, so designed the mold structure was to guarantee that the mold work utilization was reliable. Finally has carried on the examination to the mold structure and die-casting machine's match, and has drawn up a set with AutoCAD and UG two-dimensional and the three dimensional mold assembly drawing and the detail drawing.